BIXOLON SRP-500 User Manual

User’s Manual SRP-500 Inkjet Printer Rev. 1.06 http://www.bixolon.com

Rev. 1.06 - 10 -SRP-5001-2 Choosing a place for the printer 1-2-1 Avoid locations that are subject to direct sunlight or excessive heat. 1-2-2 Avoi

Rev. 1.06 - 11 -SRP-5001-3 Using the control panel Most of the functions of this printer are governed by software, but you can monitor the printer’s

Rev. 1.06 - 12 -SRP-5002. Connecting the cables CAUTION Before connecting the printer to the power supply, make sure that the voltage and power s

Rev. 1.06 - 13 -SRP-5002-2 Connecting the interface cable Connect the printer to the host ECR (host computer) though an interface cable matching the

Rev. 1.06 - 14 -SRP-5003. Setting the Dip Switches Although the factory settings are best for almost all users, if you have special requirements, yo

Rev. 1.06 - 15 -SRP-5003-1 Serial Interface (RS232C) Switch Function ON OFF Default 1-1 OFF 1-2 Emulation Selection Refer to the following tab

Rev. 1.06 - 16 -SRP-5003-2 Parallel / USB Interface (Parallel-IEEE1284) Switch Function ON OFF Default 1-1 OFF 1-2 Emulation Selection Refer t

Rev. 1.06 - 17 -SRP-5004. Setting the memory switches 4-1 Setting methods 1) Memory switch setting utility (Please check out our bundle CD) 2) Cont

Rev. 1.06 - 18 -SRP-5004-3 Star emulation 4-3-1 Setting methods 1) Memory switch setting utility (Please check out our bundle CD) 2) Control from em

Rev. 1.06 - 19 -SRP-5004-3-2 Memory switch description SW no. Description remark MSW0 Selection for the default code page MSW1 Reserved MSW2

Rev. 1.06 - 2 - SRP-500 Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any haz

Rev. 1.06 - 20 -SRP-500MSW1 details 1-5 1-4 1-3 1-2 1-1 1-0 Character Table 0 0 0 0 0 0 Page 0 (PC437 : U.S.A) 0 0 0 0 1 0 Page 2

Rev. 1.06 - 21 -SRP-5005. Installing new Ink cartridge(s) 5-1 Remove new ink cartridge from sealed pouch. (Hold cartridge by round plastic tab to av

Rev. 1.06 - 22 -SRP-5005-5 Take out old ink cartridge(s). Place new cartridge(s) into carriage. Hold plastic tab to ensure clean installation. Black

Rev. 1.06 - 23 -SRP-5006. Installing or replacing paper roll  CAUTION Notice the caution label and do not touch the auto cutter blade when you open

Rev. 1.06 - 24 -SRP-5006-3 Remove the used paper roll core if there is one. 6-4 Insert the paper roll as shown. 6-5 Be sure to note the correct dire

Rev. 1.06 - 25 -SRP-5007. Self Test The self test lets you know if your printer is operating properly. It checks the control circuits, printer mecha

Rev. 1.06 - 26 -SRP-5008. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer. This can be u

Rev. 1.06 - 27 -SRP-5009. Specification Printing method Serial ink jet matrix method Printing direction Bidirectional(logic seeking) with friction

Rev. 1.06 - 28 -SRP-50010. Appendix - Troubleshooting This chapter gives solutions to some printer problems you may have. 10-1 The printer does no

Rev. 1.06 - 29 -SRP-50010-3 You want to check the operation of the printer by itself Try to run the self test to check that the printer works proper

Rev. 1.06 - 3 - SRP-500 CAUTION Violating following instructions can cause slight wound or damage the appliance. If you observe a strange smoke,

Rev. 1.06 - 4 - SRP-500All rights reserved. No part of this publication may reproduced, stored in a retrieval, or transmitted in any form or by any m

Rev. 1.06 - 5 - SRP-500 EMC and Safety standards Applied Product Name : SRP-500 The following standards are applied only to the printers that are s

Rev. 1.06 - 6 - SRP-500 Introduction * Front view * Rear view

Rev. 1.06 - 7 - SRP-500* Dimension 226172 152 The SRP-500 is a high-quality inkjet POS printer. This one-station printer has the following feat

Rev. 1.06 - 8 - SRP-500 Table of Contents 1. Setting Up the Printer ......

Rev. 1.06 - 9 - SRP-5001. Setting Up the Printer 1-1 Unpacking Your printer box should include the items shown in the illustration below. If any it