BIXOLON SRP-350 User Manual Page 1

User’s Manual SRP-350 Thermal Printer Rev. 1.06 http://www.bixolon.com

Rev. 1.06 - 10 -SRP-3501-2-3 Parallel Interface (IEEE1284) Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe HostClk H

Rev. 1.06 - 11 -SRP-3501-2-4 USB Interface USB Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS R

Rev. 1.06 - 12 -SRP-3501-4 Setting the Dip Switches 1-4-1 Serial Interface SW Function ON OFF Default 1 Auto Line Feed Always enabled Always

Rev. 1.06 - 13 -SRP-3501-4-2 Parallel & USB Interface SW Function ON OFF Default 1 Auto Line Feed Always enabled Always disabled OFF 2 R

Rev. 1.06 - 14 -SRP-3501-5 Installing or Replacing the Paper Roll ※ NOTE Be sure to use paper rolls that meet the specifications. Do not use paper r

Rev. 1.06 - 15 -SRP-3501-5-5 Be sure to note the correct direction that the paper comes off the roll. 1-5-6 Pull out a small amount of paper, as s

Rev. 1.06 - 16 -SRP-3501-6 Adjustments and Settings The SRP-350 is set up at the factory to be appropriate for almost all users. It does, however, o

Rev. 1.06 - 17 -SRP-3501-8 Connecting the computer You need an appropriate interface cable. 1-8-1 Plug the cable connector securely into the printe

Rev. 1.06 - 18 -SRP-3502. Self Test The self-test checks whether the printer has any problems. If the printer does not function properly, contact yo

Rev. 1.06 - 19 -SRP-3503. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer. This can be u

Rev. 1.06 - 2 - SRP-350 Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any haz

Rev. 1.06 - 20 -SRP-3504. Specification Printing method Thermal line printing Dot density 180 X 180 dpi (7dots/mm) Printing width 72 mm Paper wid

Rev. 1.06 - 21 -SRP-3505. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality. In this case clean the printer a

Rev. 1.06 - 3 - SRP-350 CAUTION Violating following instructions can cause slight wound or damage the appliance. Do not use the printer w

Rev. 1.06 - 4 - SRP-350 Warning - U.S.A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to

Rev. 1.06 - 5 - SRP-350 Introduction The SRP-350 Roll Printer are designed for use with electronic instruments such as system ECR, POS, banking equ

Rev. 1.06 - 6 - SRP-350 Table of Contents 1. Setting Up the Printer ...

Rev. 1.06 - 7 - SRP-3501. Setting Up the Printer 1-1 Unpacking Your printer box should include these items. If any items are damaged or missing, pl

Rev. 1.06 - 8 - SRP-3501-2 Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector panel on the

Rev. 1.06 - 9 - SRP-3501-2-2 Serial Interface (RS-485) ON ※ When the Dip Switch is “ON” on the Serial Interface Board, DTR and RTS are connected ea