BIXOLON SLP-D400E User Manual

User's Manual Ethernet Interface Rev. 5.04 SRP-270 SRP-275 SRP-280 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 SRP-770II / 770IIE SLP-T400 / T

Ethernet Rev. 5.04 - 10 -6) Set Inactivity Time as ‘0’. [Note] - Default value is 0. Choose from 0 to 32767. - When you set Inactivity time, Ether

Ethernet Rev. 5.04 - 11 -8) When setting finishes, click Setting. [Note] Successfully finished set up Unsuccessfully finished set up - Whe

Ethernet Rev. 5.04 - 12 -6-2 DHCP interface set up 1) Turn on the printer. 2) Execute Configure Tool. [Note] - Use proper Configuration Tool

Ethernet Rev. 5.04 - 13 -4) Select MAC Address in Board list and check at DHCP Mode. [Note] - If many MAC addresses appear, refer to the MAC add

Ethernet Rev. 5.04 - 14 -6) When setting finishes, click Setting. [Note] Successfully finished set up Unsuccessfully finished set up - W

Ethernet Rev. 5.04 - 15 -8) Click Search to check given IP. 9) If the given IP is OK, click Exit.

Ethernet Rev. 5.04 - 16 -7. Web Server 7-1 Static IP interface set up 1) Execute Internet Explorer. 2) Enter IP address of the printer at Address o

Ethernet Rev. 5.04 - 17 -[Note] - If you are not aware of Subnet Mask, refer to the below. - When the IP address is (1) 1~126.xxx.xxx.xxx: Subnet Mask

Ethernet Rev. 5.04 - 18 -6) Set baud rate (Serial speed). [Note] - The baud rate (Speed) should be same as the baud rate of the printer. - The bau

Ethernet Rev. 5.04 - 19 -8) If you click the message, you can check your configuration setting. [Note] - If any change was not found after setting

Ethernet Rev. 5.04 - 2 - Table of contents 1. Interface setting Guiding...

Ethernet Rev. 5.04 - 20 - (4) Check for newer version of stored pages → Click Every visit to the page. (5) Click Refresh in Internet Explorer. 7-

Ethernet Rev. 5.04 - 21 -8. Ethernet test by using Windows test page If you don’t have any test program to check printer’s performance, you can use W

Ethernet Rev. 5.04 - 22 -4) Select Ports tab. 5) Click Add Port.

Ethernet Rev. 5.04 - 23 -6) Select Standard TCP/IP Port and click New port. 7) When standard TCP/IP printer add wizard window pops up, click Next.

Ethernet Rev. 5.04 - 24 -9) Click Next. [Note] - Click Next without any selection nor change. 10) Click Finish. 11) Click Close to close P

Ethernet Rev. 5.04 - 25 -12) Click Configure Port. 13) Enter same port number as the value of Local Port of the Ethernet interface at Raw Setting

Ethernet Rev. 5.04 - 26 -14) Click OK. 15) Select General tab and click Print Test Page to check if the printer works properly.

Ethernet Rev. 5.04 - 27 -9. How to check Static IP or DHCP 1) Start > Control panel > Network Connections. 2) Select: “Local Area Connectio

Ethernet Rev. 5.04 - 28 -4) Click “Properties”. 5) Information of network registration with Static IP 6) Information of network registration wi

Ethernet Rev. 5.04 - 29 -10. Factory Reset 1) Default setting after factory reset - Activate DHCP mode - Local Port: 9100 - Inactivity Time:

Ethernet Rev. 5.04 - 3 - How to install (Page 5) Check Network (Page 27) Static IP?DHCP Static IP Interface set up (Page16) Y NCheck the Interfa

Ethernet Rev. 5.04 - 30 -11. Function Key set up 1) How to use (1) Turn on the printer (2) Wait 10 or more seconds until the Ethernet interface boo

Ethernet Rev. 5.04 - 31 -[Appendix 1] Details of interface card Item Details Network interface 10/100 Base-T All in one (Auto detection) Protocol

Ethernet Rev. 5.04 - 32 -[Appendix 3] Setting up serial communication 1) Printer DIP switch set up Printer Baud rate & DSW set up Handshaking

Ethernet Rev. 5.04 - 33 -2) Set the baud rate (Except IFA/C-EP TYPE, SLP-T40*E, SLP-D40*E) - SRP-270,275,280: Max. 19200 bps - SRP-350: Max. 57600

Ethernet Rev. 5.04 - 4 - 2. Manual Information The purpose of this manual is to provide information on the operation and usage instructions of the Eth

Ethernet Rev. 5.04 - 5 - 4. How to install 1) Check the interface version [Note] Each version uses its own Configuration Tool. 2) Turn of the printe

Ethernet Rev. 5.04 - 6 - 5. Specifications 5-1 Hardware version Hardware version is marked on the label on the interface card bracket. IFA-E TYPE (V3

Ethernet Rev. 5.04 - 7 - 6. Configuration Tool 6-1 Static IP interface set up 1) Turn on the printer. 2) Execute Configure Tool. [Note] - Use

Ethernet Rev. 5.04 - 8 - [Note] - If Windows Security Alert pops up, please press Unblock. 4) Select MAC Address in Board list and set up Network

Ethernet Rev. 5.04 - 9 - - If you are not aware of Subnet Mask, refer to the below. When the IP address is (1) 1~126.xxx.xxx.xxx: Subnet Mask: 255.0.0